Precision-turbo-and-engine BigStuff3 GEN3 PRO SEFI (LS1) System Hardware & Bedienungsanleitung PDF herunterladen (Seite 107)

BigStuff3 Pro SEFI System (LS1)

Version 1.0 106

An example log screen is shown below. In this example, the Log Window Dashboard was setup

to collect and display Scaled Load, Scaled RPM, TPS, V bat MAP, RPM, Spark Advance and

Boost, as shown on the right side of the screen.

The left and right arrow keys on the keyboard can be used to move horizontally across the

logged data graph. As the vertical, red “cursor-line” is moved across the graph, the Log Dash

displays the actual engine operating parameters recorded at each point in the graph.

1 2 ... 102 103 104 105 106 107 108 109 110 111 112 ... 121 122

BigComm Software 1
User Instruction Manual 1
Table of Contents 2
Table of Contents Continued 3
1. Introduction 3
3. Package Contents 6
Firewall grommet 7
LS1 In-line, 1-by-4, IAC 14
Connector Pin-out 14
IAC Coils 14
Late Model 2-by-2 IAC 14
Pin-Out 15
WBO2 & 16
Coil V-Batt 16
30 Amp fuse 16
WBO2 & Coil V-Batt Relay 16
7. ECU Installation 19
8. BigComm Software Overview 19
BigComm software CD ROM 20
BigComm 24
11. Using the Tool Bar 25
BigComm desktop icon 26
13. BigComm Main Menu Screen 30
15. Closing Windows 30
16. Configuration 31
17. Hardware Configuration 31
For setup detail go to 33
Coil-on-Plug (COP) 33
Crank_Reference_Setup 33
TPS Signal in the Dash 34
19. Dwell Time Table 38
20. Load vs. RPM 40
21. Firing Order 44
22. Injector Opening Time 44
23. Injector Phase Angle 45
25. Air Fuel Ratio Table 48
26. Positive 02 Correction 52
27. Negative 02 Correction 53
30. SPARK (F4 – “Quick Key”) 56
31. Spark Table 57
32. FUEL (F3 – “Quick Key”) 60
33. Fuel Table 61
34. STARTING 64
36. After Start Delay 66
37. After Start Correction 67
38. After Start Decay 68
39. Idle 69
40. Throttle Follower 70
41. Desired Idle RPM 71
42. Idle Spark 71
43. IAC Start Position 72
44. IAC Gain Terms 73
45. Warm Up 74
48. TRANSIENT FUEL 76
51. MAP AE Decay Rate 79
52. MAP AE Inc Rate 80
53. Run Time Correction 81
54. dMAP Parameters 82
55. dTPSdt 84
56. AE Position Correction 85
57. Individual Cylinder 86
60. Boost 88
61. Boost Parameters 89
62. Boost PWM 90
63. Boost Staged 91
65. Learning 94
67. Learning Display Table 95
68. Dash 96
69. Configure Dash 96
70. Save a Dash 99
71. Load From File 101
72. Save to File 102
73. Logging (External) 104
74. Configure Log 105
76. View Log from File 106
Red cursor 109
79. Configure Replay 111
80. Upload 112
81. View Replay From File 113
Blue Ellipse represents the 116
85. Load Calibration 118
To set up, go to Gear_Box 120
To set up, go to Gears 120
87. Acronym Definition 121
88. Control Keys 121
89. Function or “Quick Keys” 121
90. Definitions 121
91. ECU Pin-out 122

Kommentare zu diesen Handbüchern

Keine Kommentare

Precision-turbo-and-engine BigStuff3 GEN3 PRO SEFI (LS1) System Hardware & Bedienungsanleitung Seite 107

Kommentare zu diesen Handbüchern

Verwandte Produkte und Handbücher für Für das Auto Precision-turbo-and-engine BigStuff3 GEN3 PRO SEFI (LS1) System Hardware &